Hot Categories
Bently Nevada | 21501-00-16-05-02 | 7200 Proximity Transducer
if you need more details,you can scan below:
Wechat Whatsapp
Detail
- Product NameBently Nevada | 21501-00-16-05-02 | 7200 Proximity Transducer
- Item NO.21501-00-16-05-02
- Weight1.0000 kg = 2.2046 lb = 35.2740 oz
- CategoryBently nevada
- BrandBently Nevada
- Creation Time2025-05-08
|
Sales Manager |
|
|
W-b |
|
Anna |
|
|
TIP CONSTRUCTION
CASE
PART NO.
DIAMETER
CONFIGURATION
TYPE THREADS
LEAD ARMOR
21500-
5 mm
Standard 1/4-28
No
21501-
5 mm
Standard 1/4-28
Yes (stainless steel)
Specifications
7200 Proximity Transducer
Maximum diameter for 21500 and 21501 probes is 0.111 in. (3.4 mm).
Specifications were determined with a -24 Vdc power supply, 10 k load, and an AISI 4140 steel target at +72°F (+22°C).
INPUT Power:-17.5 Vdc to-26 Vdc at 12 mA maximum consumption.
OUTPUT Calibrated Range: 80 mils (2.0 mm).
Begins at approximately 10 mils (0.25 mm) from probe face.
Scale Factor: 200 mV/mil (7.87 V/mm), ±4% (measured in increments of 10 mils over the calibrated range) if calibrated as a system. Within ±9.5% including interchangeability errors.
Linearity: Within 0.8 mils (0.02 mm) of a 200 mV/mil straight line if calibrated as a system. Within 2.3 mils (0.06 mm) of a 200 mV/mil straight line including interchangeability errors.
Frequency Response: 0 to 10 kHz (0 to 600,000 cpm); -5% at 10 kHz
(600,000 cpm).
Temperature Sensitivity: Typically -3% change in scale factor at +150°F (+65°C) at 50 mils gap (1.27 mm).
ENVIRONMENTAL LIMITS
Operating Temperature:
Proximitor:-60°F to +212°F (-51°C to +100°С).
Probe and Extension Cable:-30°F to +350°F (-34°C to +177°C).
Relative Humidity: To 95%, noncondensing.
Corrosion Resistance (for 8 mm probes only):
Probe operation is not affected by direct contact to the following: air, water, lube oil, ammonium hydroxide, sulfuric acid (10%), MEK (methylethylkeytone) or DMF (Dimethylformamide). System Weight: 1.3 lbs.(0.59 kg).
Refund&Replacement
1. Please contact us within 7 days if you have any question after you receiving the items.
2.The returned items has to be in its original condition, specific reason for the return, we will issue a return or
replacement for your order after we received the returns.
3.The buyer is responsible for all the shipping cost incurred.
|
Welcome to Inquiry Below |
|
|
ABB AC800M series controller I/O module | AC800F series controller module | AC31 series controller module | DCS 800xA series modules | S800 I/O modules | S900 I/O modules | Bailey INFI90 module | DSQC robot module spare parts | Advant OCS system spare parts |
|
|
Allen-Bradley ControlLogix 1756 series controller | CompactLogix 1769 series controller | SLC 500 1747 1746 Series Controller | PLC-5 1771 1785 series controller | ProSoft :MVI69/MVI56/MVI94/MVI46/3150 | Reliance Electric : Drive Boards | ICS TRIPLEX Trusted System |
|
|
Bently Nevada Chassis | I/O Module | Power supply | Communication Gateway | 3500 Monitoring system | 3300 Monitoring system | Extension Cable | Vibration and Position Cards | Reciprocating Compressor Monitors |
|
|
General Electric IC200 series | IC693 series | IC694 series | IC695 series | IC697 series | IC698 series | IC754 series | Relay module | Gas engine card |
|
|
Siemens Moore | SINAMICS | Simadyn | Simatic C1 C2 C3 | Simatic HMI | Simatic S5 S7 | 6DD series,6DP series, CPU |
|
|
Honeywell TDC2000 | TDC3000 | TPS | Experion PKS C200/C200E | Experion PKS C300 | UCN Boards | FTA Boards | ControlEdge HC900 900G03-0001 900G02-0001 | Experion LS | Experion HS | FSC Fail Safe Controller |
|
|
Etc...... |
|
Disclaimer：
1.DCSCPU sells new and surplus products and develops channels to purchase such products. This site is not approved or endorsed by any of the listed manufacturers or trademarks.
2.DCSCPU is not an authorized distributor, dealer or representative of the products displayed on this site. All product names, trademarks, brands and logos used on this site are the property of their respective owners.
3.The description, illustration or sale of products under these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.
